User Contributed MET/CAL PROCEDURE ============================================================================= INSTRUMENT: HP 7015B Sub 1 DATE: 19-Nov-97 AUTHOR: User Contributed REVISION: 0 ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 32 NUMBER OF LINES: 249 CONFIGURATION: Fluke 5700A ============================================================================= STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON 1.001 ASK+ X 1.002 ASK- R P U F W 1.003 HEAD {* COMMON MODE REJECTION TEST *} 1.004 HEAD { DC COMMON MODE REJECTION - X-AXIS } 1.005 HEAD COMMON MODE REJECTION TEST 1.006 JMP 2.001 1.007 EVAL 2.001 DISP Set the UUT front panel controls as follows: 2.001 DISP LINE ................................................ ON 2.001 DISP CHART ............................................. HOLD 2.001 DISP SERVO ............................................... ON 2.001 DISP PEN ............................................... LIFT 2.001 DISP X INPUTS/X TIME BASE ........................... X-INPUT 2.002 DISP Set the UUT front panel X & Y controls as follows: 2.002 DISP RANGE ....................................... 0.01 V/in. 2.002 DISP CAL\VERNIER ........................................ CAL 2.002 DISP NORMAL\ZERO CHECK ............................... NORMAL 2.003 DISP Connect a 1k ohm resistor between the UUT "X" (+) 2.003 DISP and (-) inputs. 2.004 DISP Connect the 5700A and the UUT as follows: 2.004 DISP 5700A TO 7015B 2.004 DISP Use "X" only 2.004 DISP OUTPUT-HI ------------> INPUT-(-) 2.004 DISP OUTPUT-LO ------------> INPUT-(Á) CHASSIS 2.005 DISP Set the UUT front panel controls as follows: 2.005 DISP PEN .............................................. WRITE 2.006 DISP Align the UUT pen at a convenient grid line 2.006 DISP near center of chart using the X and Y ZERO controls. 2.007 5700 20V S 2W 2.008 DISP Measure the difference between the final stable 2.008 DISP pen position and starting grid line in minor boxes. 2.009 MEMI Use keyboard to enter the number of measured boxes. 2.010 MEM/ 10 2.011 MATH MEM1 = 0.000 2.012 MEME 2.013 MEMC inches 0.040U 3.001 HEAD { AC COMMON MODE REJECTION - X-AXIS } 3.002 HEAD COMMON MODE REJECTION TEST 3.003 JMP 4.001 3.004 EVAL 4.001 DISP Align the UUT pen at a convenient grid line 4.001 DISP near center of chart using the X and Y ZERO controls. 4.002 5700 3.536V 60H S 2W 4.003 DISP Measure the difference between the final stable 4.003 DISP pen position and starting grid line in minor boxes. 4.004 MEMI Use keyboard to enter the number of measured boxes. 4.005 MEM/ 10 4.006 MATH MEM1 = 0.000 4.007 MEME 4.008 MEMC inches 0.031U 5.001 DISP Set the UUT front panel controls as follows: 5.001 DISP PEN ............................................... LIFT 5.002 HEAD { DC COMMON MODE REJECTION - Y-AXIS } 5.003 HEAD COMMON MODE REJECTION TEST 5.004 JMP 6.001 5.005 EVAL 6.001 DISP Connect a 1k ohm resistor between the UUT "Y" (+) 6.001 DISP and (-) inputs. 6.002 DISP Connect the 5700A and the UUT as follows: 6.002 DISP 5700A TO 7015B 6.002 DISP Use "Y" only 6.002 DISP OUTPUT-HI ------------> INPUT-(-) 6.002 DISP OUTPUT-LO ------------> INPUT-(Á) CHASSIS 6.003 DISP Set the UUT front panel controls as follows: 6.003 DISP PEN .............................................. WRITE 6.004 DISP Align the UUT pen at a convenient grid line 6.004 DISP near center of chart using the X and Y ZERO controls. 6.005 5700 20V S 2W 6.006 DISP Measure the difference between the final stable 6.006 DISP pen position and starting grid line in minor boxes. 6.007 MEMI Use keyboard to enter the number of measured boxes. 6.008 MEM/ 10 6.009 MATH MEM1 = 0.000 6.010 MEME 6.011 MEMC inches 0.040U 7.001 HEAD { AC COMMON MODE REJECTION - Y-AXIS } 7.002 HEAD COMMON MODE REJECTION TEST 7.003 JMP 8.001 7.004 EVAL 8.001 DISP Align the UUT pen at a convenient grid line 8.001 DISP near center of chart using the X and Y ZERO controls. 8.002 5700 3.536V 60H S 2W 8.003 DISP Measure the difference between the final stable 8.003 DISP pen position and starting grid line in minor boxes. 8.004 MEMI Use keyboard to enter the number of measured boxes. 8.005 MEM/ 10 8.006 MATH MEM1 = 0.000 8.007 MEME 8.008 MEMC inches 0.031U 9.001 DISP Set the UUT front panel controls as follows: 9.001 DISP PEN .......................... LIFT 9.002 DISP Remove 1 k ohm resistor from UUT inputs. 9.003 HEAD {* ACCURACY TEST *} 9.004 HEAD { X-AXIS CALIBRATION } 9.005 HEAD ACCURACY TEST 9.006 JMP 10.001 9.007 EVAL 10.001 ASK+ U 10.002 DISP Connect the 5700A and the UUT as follows: 10.002 DISP 5700A TO 7015B 10.002 DISP Use "X" only 10.002 DISP OUTPUT-HI ------------> INPUT-(+) 10.002 DISP OUTPUT-LO ------------> INPUT-(-) 10.003 DISP Set the UUT front panel controls as follows: 10.003 DISP PEN .............................................. WRITE 10.004 5700 0V S 2W 10.005 DISP Using the UUT ZERO controls, position pen to exactly 10.005 DISP zero on the X-axis (left most line on paper). 10.006 MESS .1 Volts = 10 major boxes. 10.007 5700 0.1000V 0.00030U 2W 11.001 5700 0V S 2W 11.002 DISP Using the UUT ZERO controls, position pen to exactly 11.002 DISP zero on the X-axis (left most line on paper). 11.003 MESS .1 Volts = 10 major boxes. 11.004 5700 0.01000V 0.00030U 2W 12.001 5700 0V S 2W 12.002 DISP Using the UUT ZERO controls, position pen to exactly 12.002 DISP zero on the X-axis (left most line on paper). 12.003 MESS .1 Volts = 10 major boxes. 12.004 5700 0.02000V 0.00030U 2W 13.001 5700 0V S 2W 13.002 DISP Using the UUT ZERO controls, position pen to exactly 13.002 DISP zero on the X-axis (left most line on paper). 13.003 MESS .1 Volts = 10 major boxes. 13.004 5700 0.03000V 0.00030U 2W 14.001 5700 0V S 2W 14.002 DISP Using the UUT ZERO controls, position pen to exactly 14.002 DISP zero on the X-axis (left most line on paper). 14.003 MESS .1 Volts = 10 major boxes. 14.004 5700 0.04000V 0.00030U 2W 15.001 5700 0V S 2W 15.002 DISP Using the UUT ZERO controls, position pen to exactly 15.002 DISP zero on the X-axis (left most line on paper). 15.003 MESS .1 Volts = 10 major boxes. 15.004 5700 0.05000V 0.00030U 2W 16.001 5700 0V S 2W 16.002 DISP Using the UUT ZERO controls, position pen to exactly 16.002 DISP zero on the X-axis (left most line on paper). 16.003 MESS .1 Volts = 10 major boxes. 16.004 5700 0.06000V 0.00030U 2W 17.001 5700 0V S 2W 17.002 DISP Using the UUT ZERO controls, position pen to exactly 17.002 DISP zero on the X-axis (left most line on paper). 17.003 MESS .1 Volts = 10 major boxes. 17.004 5700 0.07000V 0.00030U 2W 18.001 5700 0V S 2W 18.002 DISP Using the UUT ZERO controls, position pen to exactly 18.002 DISP zero on the X-axis (left most line on paper). 18.003 MESS .1 Volts = 10 major boxes. 18.004 5700 0.08000V 0.00030U 2W 19.001 5700 0V S 2W 19.002 DISP Using the UUT ZERO controls, position pen to exactly 19.002 DISP zero on the X-axis (left most line on paper). 19.003 MESS .1 Volts = 10 major boxes. 19.004 5700 0.09000V 0.00030U 2W 20.001 DISP Set the UUT front panel X-axis controls as follows: 20.001 DISP RANGE ........................................ 0.1 V/in. 20.002 5700 0V S 2W 20.003 DISP Using the UUT ZERO controls, position pen to exactly 20.003 DISP zero on the X-axis (left most line on paper). 20.004 MESS 1 Volt = 10 major boxes. 20.005 5700 1.0000V 0.0020U 2W 21.001 DISP Set the UUT front panel X-axis controls as follows: 21.001 DISP RANGE .......................................... 1 V/in. 21.002 5700 0V S 2W 21.003 DISP Using the UUT ZERO controls, position pen to exactly 21.003 DISP zero on the X-axis (left most line on paper). 21.004 MESS 10 Volt = 10 major boxes. 21.005 5700 10.000V 0.020U 2W 22.001 DISP Set the UUT front panel controls as follows: 22.001 DISP PEN ............................................... LIFT 22.002 MESS 22.003 HEAD { Y-AXIS CALIBRATION } 22.004 HEAD ACCURACY TEST 22.005 JMP 23.001 22.006 EVAL 23.001 DISP Connect the 5700A and the UUT as follows: 23.001 DISP 5700A TO 7015B 23.001 DISP Use "Y" only 23.001 DISP OUTPUT-HI ------------> INPUT-(+) 23.001 DISP OUTPUT-LO ------------> INPUT-(-) 23.002 DISP Set the UUT front panel Y-axis controls as follows: 23.002 DISP RANGE ....................................... 0.01 V/in. 23.002 DISP PEN .............................................. WRITE 23.003 5700 0V S 2W 23.004 DISP Using the UUT ZERO controls, position pen to exactly 23.004 DISP zero on the Y-axis (bottom most line on paper). 23.005 MESS .07 Volts = 7 major boxes. 23.006 5700 0.07000V 0.00021U 2W 24.001 5700 0V S 2W 24.002 DISP Using the UUT ZERO controls, position pen to exactly 24.002 DISP zero on the Y-axis (bottom most line on paper). 24.003 MESS .07 Volts = 7 major boxes. 24.004 5700 0.01000V 0.00021U 2W 25.001 5700 0V S 2W 25.002 DISP Using the UUT ZERO controls, position pen to exactly 25.002 DISP zero on the Y-axis (bottom most line on paper). 25.003 MESS .07 Volts = 7 major boxes. 25.004 5700 0.02000V 0.00021U 2W 26.001 5700 0V S 2W 26.002 DISP Using the UUT ZERO controls, position pen to exactly 26.002 DISP zero on the Y-axis (bottom most line on paper). 26.003 MESS .07 Volts = 7 major boxes. 26.004 5700 0.03000V 0.00021U 2W 27.001 5700 0V S 2W 27.002 DISP Using the UUT ZERO controls, position pen to exactly 27.002 DISP zero on the Y-axis (bottom most line on paper). 27.003 MESS .07 Volts = 7 major boxes. 27.004 5700 0.04000V 0.00021U 2W 28.001 5700 0V S 2W 28.002 DISP Using the UUT ZERO controls, position pen to exactly 28.002 DISP zero on the Y-axis (bottom most line on paper). 28.003 MESS .07 Volts = 7 major boxes. 28.004 5700 0.05000V 0.00021U 2W 29.001 5700 0V S 2W 29.002 DISP Using the UUT ZERO controls, position pen to exactly 29.002 DISP zero on the Y-axis (bottom most line on paper). 29.003 MESS .07 Volts = 7 major boxes. 29.004 5700 0.06000V 0.00021U 2W 30.001 DISP Set the UUT front panel Y-axis controls as follows: 30.001 DISP RANGE ........................................ 0.1 V/in. 30.002 5700 0V S 2W 30.003 DISP Using the UUT ZERO controls, position pen to exactly 30.003 DISP zero on the Y-axis (bottom most line on paper). 30.004 MESS .7 Volts = 7 major boxes. 30.005 5700 0.7000V 0.0020U 2W 31.001 DISP Set the UUT front panel Y-axis controls as follows: 31.001 DISP RANGE .......................................... 1 V/in. 31.002 5700 0V S 2W 31.003 DISP Using the UUT ZERO controls, position pen to exactly 31.003 DISP zero on the Y-axis (bottom most line on paper). 31.004 MESS 7 Volts = 7 major boxes. 31.005 5700 7.0000V 0.02U 2W 32.001 DISP Set the UUT front panel controls as follows: 32.001 DISP PEN ............................................... LIFT 32.002 MESS 32.003 END